When my PC’s storage is almost full, or if it’s infected with malware that refuses to go away, I often turn to the ultimate solution: resetting Windows. But just how long does it take to reset a PC? Many factors influence the duration, such as the amount of storage, the status of the OS, and more.

Key Takeaways

• The duration of a PC reset depends on the chosen method and the computer’s specifications. Simple resets can take 30 minutes to a few hours, while more comprehensive ones may take several hours.
• Many factors are responsible for increasing the duration, such as software glitches, overheating, hardware problems, and malware.
• Back up important data to an external drive or the cloud before resetting so you won’t lose essential files.

Based on several factors, PC reset times can vary from 30 minutes to 3 hours. These include your storage device, the volume of data, and the files you wish to preserve. In some cases, particularly on sluggish computers, a reset can extend to an entire day.

There are two ways to reset a Windows PC to remove corrupt data or persistent bugs. You can either choose Keep My Files or Remove Everything.  When I chose to keep my data and files, the process took about 30 to 45 minutes.

On the other hand, if you go with removing everything, it may take anywhere from 2.5 to 3 hours for a complete reset. This is because the PC takes time to clean all the files and data on the hard drive.

Factors Affecting PC Reset Duration

Numerous factors affect the time it takes to reset a PC:

• CPU Speed: A faster processor can handle data processing tasks more quickly.
• RAM Size: Sufficient RAM allows for smoother multitasking and data handling during reset.
• HDD vs SSD: Solid-state drives (SSDs) generally offer faster read and write speeds than traditional hard disk drives (HDDs). Upgrading to an SSD can significantly reduce reset times.
• Amount Of Data: The total amount of data on the computer affects the time it takes to reset. If there’s a large amount of data to be processed, the reset will take longer.
• Condition Of Operating System: The overall health and condition of the existing operating system can influence the reset time. A system with many errors or corruption may take longer to reset.

Taking proactive measures, such as ensuring software compatibility and monitoring system health, helps me minimize the need for frequent resets, which allows computer stability and longevity. In addition, I always back up my critical data to an external USB drive before a reset to be on the safe side; hence, I suggest you do the same.

• How To Clear PC Cache? 
• How To Change IP Address?
• How To Remove Malware And Viruses From PC?

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

How Long Does it Take To Reset A PC? [SOLVED] is a post from Tech4Gamers - All About Technology And Gaming News

Key Takeaways

• Scaling means adjusting the size and quality of an image to fit a specific display or output device.
• You can choose between Aspect Ratio, Full Screen, Custom, and No Scaling options.
• Remember that it can affect the image or video quality, causing them to appear blurred or distorted.

GPU Scaling

Modern GPUs have powerful engines that can perform scaling operations quickly and efficiently. GPU scaling is used when the display’s resolution does not match the content’s resolution.

For example, if a 1080p video is played on a 4K display, the image will appear smaller than the screen’s full size. It can adjust the video size to fit the screen’s full size, preserving the aspect ratio and avoiding distortion.

Upscaling

Upscaling is often used when displaying older content or content designed for lower-resolution displays on modern high-resolution displays by increasing the resolution of an image or content to match that of a higher-resolution display.

The GPU adds pixels to the image and employs interpolation algorithms to estimate the color values of the new pixels. For example, when playing a DVD movie on a 4K TV, the GPU will upscale the DVD’s 480p resolution to fit the 4K display’s 2160p resolution.

Downscaling

Downscaling displays high-resolution content on lower-resolution displays, like connecting a high-end gaming PC to a lower-resolution monitor by decreasing the resolution of an image or content to fit a lower-resolution display. The GPU achieves this by removing pixels from the image and using interpolation algorithms to estimate the color values of the remaining pixels. 

Performing GPU Scaling

Know the purpose of different settings:

• Aspect Ratio Scaling: Preserves the original aspect ratio of an image, preventing stretching or compression. If the image’s aspect ratio differs from your monitor’s, black bars appear on the sides to fill the screen.
• Full Screen: Stretches the image to fit the screen, potentially distorting it if the aspect ratios differ significantly.
• No Scaling: Displays the image in its original size without stretching or resizing.

Here is how to proceed:

1. Right-click on your Desktop > Choose NVIDIA Control Panel or AMD Radeon Software, depending on your installed GPU.

   

2. Select Display > Adjust Desktop Size And Position > Choose the monitor you want to adjust from the drop-down menu if multiple displays are connected to your GPU.
3. Under Scaling, you’ll see a drop-down with Aspect Ratio, Full Screen, and No Scaling options.
4. If the image is smaller than your screen’s resolution, it will be displayed in the center of your screen with black borders on all sides.

   

5. If you’re having blurry images or text trouble, adjust the Override The Scaling Mode Set By Games And Programs option to On > Apply.

On the other hand, learn what to do if the NVIDIA control panel is crashing or missing essential options in the interface.

Display Scaling

The only different option here is Custom Scaling. It allows you to set a custom scaling percentage, which can be helpful if you have a high-resolution monitor and find that text and images are too small to read comfortably. 

Follow the instructions below:

1. Access the Desktop > Right-click on the screen > Display Settings > Advanced Display Settings.

   

2. Under Resolution, select Advanced Scaling Settings.
3. If you’re having trouble with blurry apps or text, turn on the toggle, Let Windows Try To Fix Apps So They’re Not Blurry.
4. In Scaling, there will be a drop-down with Keep the Aspect Ratio, Custom Scaling, Full Screen, and No Scaling.
5. If you have multiple monitors connected, adjust the scaling settings for each monitor individually.

Advantages Of GPU And Display Scaling

Scaling offers many benefits to the user, such as the ones discussed below. Personally, I experienced better quality game graphics after scaling my GPU. 

GPU Scaling 

Performing this can:

• Result in a sharper, more detailed image than display scaling, especially if you’re stretching a lower-resolution image.
• Be useful if you’re playing a game or watching a video that doesn’t support your monitor’s native resolution or want to stretch a lower-resolution image to fill your entire screen.
• Reduce input lag, as the graphics card can handle scaling faster than the monitor.
• Eliminate jagged edges or aliasing in some games or videos.

Display Scaling

With this, you can:

• Adjust the size of individual elements on your screen, which can be more precise than resizing the entire image.
• Improve the readability of text and other elements on your screen, especially on high-resolution monitors.

I found GPU scaling and display scaling useful tools for adjusting the resolution and scaling of content on my computer screen. However, I had to do some trial and error by modifying the adjustments to balance the resolution, scaling, and performance. With the wrong configurations, the image may look awkward.

More About PCs:

• How To Turn Off Mouse Acceleration? [Windows 11]
• SOLVED: How To Get Into BIOS [Windows 11]
• How To Lock Computer With Keyboard? [All Methods]

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

How To Perform Scaling On GPU And Display? is a post from Tech4Gamers - All About Technology And Gaming News

Key Takeaways

• TPM 2.0 is vital for running Windows 11 and is primarily used for identity and data protection.
• Enabling TPM 2.0 involves accessing BIOS/UEFI settings, finding the TPM option in the Security or Advanced section, and enabling it to enhance security.
• Check whether your PC has TPM 2.0 through the PC Health Check app.

Verify TPM 2.0 Compatibility

To install Windows 11, confirm that your PC has TPM 2.0. You can utilize Microsoft’s PC Health Check tool for compatibility verification. After running the test, the tool will indicate whether your device meets the requirements. For a more detailed evaluation, click See All Results to check if TPM 2.0 is enabled on your PC, as activation may be necessary.

Verify TPM 2.0 status:

1. Open PC Settings > Update and Security option > Windows Security.
2. Ensure that you choose Specification 2.0 Version in the Security Processor section. If the number differs, your computer may be incompatible with the latest Windows.

Determine whether TPM 2.0 is available by checking the Microsoft Management Console:

1. Press Windows + R keys > In the Run box, enter tpm. msc.
2. The TPM could be inactive on your computer if it displays the warning, Compatible TPM Cannot Be Detected. Otherwise, check the Specification Version in TPM Manufacturer Information. If it is lower than 2.0, the TPM may not work. 

How To Activate Through BIOS?

The BIOS contains and manages the crucial PC settings, including the TPM. If you have the right TPM installed, the next step is to activate it in the BIOS.

AMD Motherboards

Follow these steps:

1. Press F2 or Delete continuously when the computer is booting to access BIOS.
2. Press F7 to enter Advanced Mode > Click on the drop-down > Choose Settings.
3. Look for Security > Choose Security Device Support.
4. Go to AMD fTPM Switch > Change AMD fTPM to [AMD fTPM].

Intel Motherboards

Here are the steps you must follow:

1. Open BIOS > Press F7 for Advanced Mode.
2. Enter Settings > Security.
3. Click on Trusted Computing > Security Device Support > Change the status to Enable.
4. Finally, head to TPM Device Selection > Enable PTT security.

ASUS Motherboards

Take note of the following steps:

1. Continue pressing the Delete button while the computer is booting up.
2. Go to Advanced > PCH-FW > Look for PTT > Select Enable > OK.
3. Press F10 > Restart the computer.

Can I Activate TPM 2.0 In Gigabyte BIOS Auros?

I used the following methods to enable TMP 2.0 Gigabyte BIOS for AMD and Intel motherboards, and they were quick and effective in performing the required task.

AMD Motherboards

Here is what I did:

1. Restart PC > Press the Delete key > Hold it once the boot screen pops up.
2. Go to Advanced Mode > Press F2 to activate TPM.
3. Navigate to Settings > Miscellaneous > Choose AMD CPU FtPM > Save and Exit > Restart your PC.

Intel Motherboards

These are the steps you should follow:

1. Restart your computer > Hold the Delete key until there is a beep.
2. Hit F2 for Advanced Settings > Navigate to Intel Platform Trust Technology (PTT) > Select Enabled > Save the changes and exit.

Primary Functions Of TPM

Here is a look at the primary reasons for incorporating TPM:

• Managing And Storing Passwords
• Encrypting Hard Disk Partitions
• Maintaining Platform Integrity

As per my research, enabling TPM 2.0 brings several security perks, as discussed above. Therefore, I recommend making the best use of this feature if it is compatible with your Windows. Remember that different manufacturers have varying terms for the TPM. So, double-check by learning about the specific name used by your CPU’s manufacturer on their official website.

Similar PC Guides:

• How To Check What Motherboard I Have? [All Methods]
• How To Change IP Address? [PC And Smartphone]
• How To Turn Off Overclocking? [Explained]

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

How to Enable TPM 2.0? [Step By Step With Images] is a post from Tech4Gamers - All About Technology And Gaming News

Key Takeaways

• Freezing or locking your computer screen prevents unauthorized access to your system while you are away.
• The easiest way to lock the Windows OS screen is to press the Windows + L or Ctrl + Alt + Delete and select the Lock option.
• Use the Control + Command + Q keys simultaneously to freeze a macOS screen.

On Windows 7

You can freeze your Windows 7 screen using five straightforward methods that worked like a charm for me. However, I would advise you to upgrade to newer versions if you are still on Windows 7 since it is outdated and missing many new features. 

Keyboard Shortcut

I pressed the Windows + L keys simultaneously and noticed that my computer screen quickly went to the login page, thereby locking the system.

Start Menu

Here is what you need to do:

1. Launch the Start menu > Click the arrow next to the Shutdown button > Choose Lock.
2. This will lock the computer’s screen, and you will be taken to the welcome screen.

Screen Lock Shortcut

You can create a shortcut as well:

1. Right-click on Desktop> New > Shortcut.
2. Enter the following command:

   Rundll32.exe User32.dll, LockWorkStation

3. Click Next > Give the shortcut a proper name, for example, Lock Screen.
4. The Lock Screen icon will now be visible on your Desktop.
5. Right-click the icon > Properties > Select the Shortcut tab > Change Icon.

   

6. Enter the following command in the search field, Look For Icons In This File:

   C:\Windows\System32\imageres.dll

7. A list of icons will be displayed > Select the desired icon > OK.
8. Click on the Run drop-down > Minimized > OK.

   

9. Double-click on the icon to freeze your screen.

Using Shortkeys 

Use the method below:

1. Press the keys Ctrl + Alt + Delete simultaneously > Lock This Computer.
2. This will lock your computer screen.

Automatic Screen Lock

Set up an Auto Lock on Windows 7:

1. Open the Start menu > Control Panel > Personalization.
2. Come to Screen Saver tab > Enter desired time duration in the Wait box > Mark the checkbox, On Resume, Display Logon Screen > OK.

   

3. The screen will lock after the specified duration of inactivity.

On Windows 8

Apart from the combination of Windows + L and Ctrl + Alt + Delete, there is one other method that I use to freeze my Windows 8 screen.

Using Windows Key

This is what you should do:

1. Launch the Start menu > Click the User Account Picture Icon > Lock.

   

2. Your screen will be locked.

On Windows 10 & 11

Again, as I mentioned for Windows 8, the standard keyboard shortcuts also apply to both these versions. Furthermore, you can resort to additional effective ways to lock the screen.

Start Menu

Here is what I did:

1. Get to the Start menu > Click on User Account Icon >  Lock.
2. This will lock your computer’s screen.

Automatic Screen Lock

Automatically lock or freeze after a certain period of inactivity: 

1. Access the PC Settings > Personalization > Lock Screen > Select a background.
2. Again, choose Lock Screen > Screen Timeout Settings.
3. Alter the time duration under the Screen heading to set up automatic screen locking after the specified time.

   

Dynamic Lock

Using the built-in Dynamic Lock utility, configure your Windows to lock the computer screen automatically:

1. Open the Settings > Accounts > Sign-In Options.

   

2. Scroll down to the Dynamic Lock section > Mark the box, Allow Windows To Automatically Lock Your Device When You’re Away.

On Mac OS

Freezing the screen on your Mac is a bit different than doing it on Windows. Although, I found the process very easy.

Keyboard Shortcut

Follow these steps:

1. Press the Command + Option + Shift + Q simultaneously.
2. This will log out of the current User Account, close all the running applications and tabs on the system, and lock the screen.

Using Command + Shift + Q Key

I pressed Command + Shift + Q, which immediately locked the screen. Additionally, this method will display a confirmation prompt before logging out of your user account. Make sure to save your progress.

Using Control + Command + Q Keys

Press the Control + Command + Q keys. Doing this will lock the screen and redirect you toward the login screen. Plus, it lets you log into the account using your password or Touch ID and will not close any running applications.

Apple Menu

Proceed as mentioned below:

1. Go to the Apple menu > Lock Screen.
2. This will freeze your computer screen.

On OS X Yosemite/ El Capitan

I came across two methods to lock the screen on the OS X Yosemite or El Capitan on Mac. Upon testing, both were equally effective.

Menu Bar

This is among the easiest techniques. Simply click the Lock icon on the upper Menu Bar, which will instantly lock the screen on your Mac.

Keyboard Hotkeys

There are the keys you can use:

1. Press Control + Shift + Eject keys simultaneously if your Mac has an Eject Key or an Internal Optical Drive.
2. Alternately, press the Control + Shift + Power keys.
3. This will lock the screen on your Mac device.

On A Projector

If you use a projector and want to freeze the screen to hide your computer screen activity, use the projector’s remote control. Many projectors offer the option to freeze the projected display remotely.

However, not all projectors have this option. In that case, I found two ways to proceed through the computer’s OS. 

Extend Option

Move ahead with these instructions:

1. Click the Notifications Icon on the Taskbar to launch the Action Center > Project.

   

2. Pick Extend > This will lock your computer’s projected screen.

   

PC Screen Only Option

You can also black out your projector’s display. To do that:

1. Again, click the Notifications icon on the Taskbar > Project.
2. Choose PC Screen Only to black out the computer’s projected screen.

   

I recommended locking or freezing your computer screen while you are away to maintain privacy and prevent unauthorized access. Unlike the sleep or hibernation option, it also allows your processes and programs to run in the background, hence, I found it super useful.

Similar Guides:

• How To Lock Computer With Keyboard? [All Methods]
• How To Remove PIN From Windows 11? [ALL METHODS]
• All Methods To Restart Computer With Keyboard
• How To Shut Down Laptop From Keyboard? [Mac & Windows]

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

How To Freeze A Computer Screen [All Platforms + Windows] is a post from Tech4Gamers - All About Technology And Gaming News

Key Takeaways

• You can wire RGB LED strips without a controller in different ways, like an external supply, battery pack, or Arduino microcontroller.
• Connect each color to a separate power source, like a battery or power supply, to control the individual colors.
• To get fading color effects, you can use an Arduino board.

Things to Know Before You Can Wire RGB LED Strip Without A Controller

Before attempting to wire an RGB LED strip without a controller, here are a few things to know that will help you with the techniques ahead.

Determine The Voltage Lines

Each LED bulb typically consists of three colored wires: white or grey for the ground wire (transmitting electricity back to the circuit), red for the positive wire (carrying a positive charge), and black for the negative wire (carrying electricity).

Know The Wiring Process

Once you know what each wire in your RGB LED strip does, connect them to a power source. For each color of your RGB strip, there will be a pair or trio of wires you need to connect to a power source. That means you’ll have to connect the positive, negative, and ground wires separately for the red, green, and blue bulbs. 

Data Controller Connection

The data controller is what moves the pixels to display the desired color. You can solder the end of a data connector to the RGB LED strip with some wire connectors. Once you do that, it passes signals through the wire, changing the lights based on your commands.

Identifying Wires and Connecting Them

Each light on the RGB LED strip is a pixel with three prongs: positive, negative, and ground. Connect the ground, positive, and negative wires on the power supply to those of the RGB LED strip.

How To Wire RGB LED Strip Without A Controller

Before trying out one of the methods, take some time to identify the positive and negative wires in your LED strip. You’ll also have to determine which voltage line connects to each color.

Using An External Power Supply

Use an external power supply to get specific colors when you have leftover RGB LED strips without a controller. For this method, arrange a soldering kit and a 12v power supply, such as a wall adapter. You can also use a micro USB cable for the power supply, but if it delivers a higher voltage, get a converter to avoid damaging your RGB LED strip.

Here are the steps you can follow:

1. Strip the wire on the adapter cable to expose the red and black wires.
2. Notice the four points labeled +12v, G, R, and B on your RGB LED strip.
3. Solder the red wire, which is the positive wire, to the pad labeled +12v.
4. Then, solder the black or ground wire to the pad corresponding to your desired color.
5. If you want blue-colored lights, touch the ground wire to the pad labeled B; for green lights, touch it to the pad labeled G.

Mixing Colors

Of course, you won’t be limited to the primary red, blue, or green colors since this method allows you to mix colors. Just take an extra bit of wire and solder one end to the same pad as the ground wire and the other to the color you want to mix with. So, if you soldered the ground wire to the blue pad, mix it with red to get a purple effect.

Controlling Individual Colors

In case you want to control individual colors rather than sticking to a single color, you’ll have to repeat the process for each color. That means soldering a separate power supply to each color pad. Then, you can turn on the power supply that corresponds to your desired color and turn off the one you don’t want. 

Wiring Your RGB LED Strip To A Battery Pack

A simpler way to control the colors of your RGB LED strip is by wiring it to a battery pack. Instead of an external power supply, I used a battery pack to power the strip.

Moreover, you will need a battery pack and clip. Connect the positive wire to the +12v pad and the ground wire to one of the color pads. On the other hand, connect a battery to each color pad on the strip instead of just a single pad to control all the colors of your RGB LED strip.

One issue I found with this method is that I could not control how brightly the colors lit up. On the other hand, you reduce the risk of frying your LEDs since the batteries will run out before the wires overheat. 

Using Arduino Board

While the ways mentioned above allow you to control which color your RGB LED strip displays at a time, they can’t give you the desired effects. I tested an Arduino Microcontroller Board by directly connecting the positive, negative, and ground wires to it.

Usually, the average 12v RGB LED strips, also known as SMD5050, come with infrared remote control, but when you don’t have one, Arduino can help you get a custom fading effect. 

What You’ll Need

To connect an Arduino to your 12v LED strip, gather the following parts: 

• A 12v RGB LED strip
• 1 Arduino UNO Board
• 3 10k resistors
• Hookup wires
• 3 N-Channel MOSFETs (make sure they’re Logic Level)
• 12v power supply
• A breadboard

You’ll need Metal Oxide Silicon Field Effect Transistors (MOSFETs) when trying to control a component with a higher voltage than your Microcontroller, as they prevent it from overheating and frying. Namely, MOSFETs have three terminals: the source (S), drain (D), and gate (G). The voltage that passes through the gate terminal controls the current passing through the drain and source terminals.

Moreover, a major benefit of using MOSFETs is that you can pass each color of your LED strip through the MOSFET to control how bright each color on your LED strip is. I recommend getting Logic-Level MOSFETs instead of standard ones because it ensures the Arduino setup will work the way you want.

Connecting The Circuit

You can set up an Arduino and MOSFET circuit by following these steps:

1. You’ll find numbered pins on the Arduino board> Connect the pins marked 5, 6, and 9 to the Gate Terminals of the three MOSFETs.
2. Connect a 10k resistor in line with each gate terminal, securing each to the Ground Rail.
3. Connect the Source Terminals to the Ground Rail of the board.
4. Connect your LED strip’s red, blue, and green connectors to the Drain Terminals.
5. Take the 12v connector of your LED strip > Connect it to the Power Rail > Connect the Ground Pin of your Arduino board to the Ground Rail.
6. Take your 12v power supply > Connect it to the Power Rail.

LED strips usually come with Dupont connectors, which make it easy to connect the strip to Arduino. In case your strip doesn’t have connectors, solder the wires to your LED strip and power the board through the USB port. 

Fading The Lights

Next, connect your computer to the Arduino board through a USB cable:

1. Launch the Arduino IDE on your computer > Select the right port and board numbers for your board.
2. Navigate first to Tools > Port and then Tools > Board. Open up a new sketch file > Save it with a suitable name.

This Arduino sketch will fade the lights on your RGB strip, one color at a time. The lights will then stay on for a few seconds before fading completely.

To make the code, you’ll have to add the following:

• Define which pins will control the MOSFETs.
• Has an overall brightness variable of 255.
• Have individual variables for each color.
• Create a variable to control how quickly the colors will fade, which we’ll call our fadeSpeed value.
• In the setup function, set the Arduino pins as the output.
• Write the code for the TurnOn() method as 3 ‘for‘ loops that take red, blue, and green lights to their maximum brightness over a particular time.
• Write the TurnOff() method code by applying the brightness variable to the red, blue, and green color pins, effectively taking them to zero over time.  

Testing The Sketch

The TurnOn() and TurnOff() methods should be empty loop methods to prevent errors during compilation. In the end, your code should look like this:

After completing the sketch, save the file, verify it, and upload it to the board. When it works, you’ll see that each color on your 12v RGB LED strip lights up individually; the white light stays for 5 seconds and then fades completely.

I found these techniques effective when I misplaced my RGB controller. Although using an Arduino board was a bit technical, I effectively achieved transition effects in RGB  with the above steps. Before picking a method, determine whether you want solid colors or color effects, and proceed accordingly.

More About RGBs:

• RGB In Gaming: Everything To Know
• Explained: How To Change RGB On AMD Wraith Prism Cooler?
• How To Fix RGB Fusion Not Working [2023]

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

How To Wire RGB LED Strip Without A Controller? is a post from Tech4Gamers - All About Technology And Gaming News

Key Takeaways

• Connecting the USB cable lets you control the Wraith Prism cooler’s three RGB lights (ring, logo, and fan). 
• AMD Wraith Prism RGB Lighting Control Software is designed to control the AMD cooler’s RGB.
• Other software include OpenRGB, ASUS Aura Sync, and Gigabyte RGB Fusion.

Connect The USB Cable

To control the RGB lights on your cooler, I plugged the USB cable into the cooler and ensured the RGB cable was disconnected. Using both cables simultaneously may prevent RGB from working. Then, I removed the rubber coverings on the cooler’s USB port, connected the 3-pin USB header, and attached the other end to a USB Type-2 port on my motherboard.

Change AMD Wraith Prism RGB On Windows

I used the AMD Wraith Prism RGB Lighting Control, which is specifically designed for this cooler. It provides loads of customizable options and is very easy to use. 

I adjusted each option in the software to experiment with different RGB colors and effects. Save your themes as .SR4 files by clicking Export, and import themes by selecting a .SR4 file through the Import option.

Motherboard Specific Software

Following is the list of motherboard-specific software supported by AMD’s Wraith Coolers:

• Gigabyte RGB Fusion
• MSI Mystic LighSRock Polychrome Sync
• ASUS Aura Sync
• Biostar Vivid LED DJ

Changing AMD Wraith Prism RGB On Linux And Mac

There is no official software from AMD/Cooler Master or the different motherboard manufacturers that work on Linux or Mac. I had to use third-party software to control the cooler’s RGB for these operating systems.

Thankfully, there are a lot of options available:

• OpenRGB: Supports both Windows, Linux, and Mac and can sync all your RGB peripherals.

  

• CM_RGB: Supports Windows, Linux, and Mac.
• Wraith Master: Only supports Linux.

Changing the RGB on my AMD Wraith Cooler was not difficult because the above-mentioned software are pretty easy to navigate and understand. Just make sure to plug in the USB cable provided with the cooler, and I could change all three RGB lights on the cooler for a customized look.

More About RGBs:

• How To Fix RGB Fusion Not Working [2023]
• How To Reset RGB LED Controller
• How To Wire RGB LED Strip Without A Controller
• ASRock Polychrome RGB Not Working

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

How To Change RGB On AMD Wraith Prism Cooler? is a post from Tech4Gamers - All About Technology And Gaming News

Key Takeaways

• There are many ways to reset an RGB LED controller, such as using the reset hole or reinstalling the batteries.
• Resetting the controller may fix issues caused by weak batteries, interference between remote and LED signals, or improper pairing of the LED strips to the remote.
• A faulty RGB LED controller or LED strips can also be the reason behind the malfunction.

Using The Reset Button On The Remote

One of the most common methods is using the remote’s Reset button. I performed it as the first troubleshooting step, which worked effectively in my case. On the other hand, you can also wire a RGB LED strip without a controller when it fails to function.

Here’s how to carry it out: 

1. Find a small hole next to a Reset label, usually located at the back of the remote. 
2. Insert something small and sharp into it, like a hairpin or a safety pin, until you hear a popping sound > Hold for 3 to 5 seconds > Let go.

Factory Reset

This method is carried out in a similar way to the above process. Please note that this method will completely reset your remote’s settings, and you will need to reprogram the remote with the LED strips. For this, refer to the manual provided with the package. 

Use the method below:

1. Again, insert the same object into the Reset hole > Press until LED lights flash on the remote, typically about 10 seconds. 
2. Remove the remote’s batteries > Wait 5 minutes > Reinsert them > Turn on the remote.

Reinstalling The Batteries On The Remote

The next thing I tried was to replace the batteries on the remote. The battery compartment is usually located at the bottom of the remote. 

Carefully proceed with the steps: 

1. Pull out the battery holder > Remove the battery.

   

2. Hold the remote’s Power button for 10 to 15 seconds.
3. Reinstall the battery > Place the compartment back into the remote.
4. Replace the batteries if the problem persists.

Using The Remote And Power Adapter

You can use the remote and Power Adapter simultaneously to run a reset. It involves restarting the LED strips, and after doing so, paired with other steps, my remote returned to its normal operation.

This is what you need to do:

1. Turn on the LED strips for a few seconds > Turn off > Remove the power source of the LED strips. 
2. Hold the remote’s Power button for a few seconds >  Re-plug the LED strips’ Power Adapter. 

   

3. Continue pressing the Power button. 
4. The LED strips should alternate between red, green, blue, and yellow colors before switching off. 

Using The Remote And Power Adapter: Alternative Method

This is an alternate method I tried to reset my remote. It is based on reprogramming the remote to rule out any faulty settings.

Here’s how this one goes: 

1. Turn on the LED strips for a few seconds > Turn off > Remove the Power Adapter, but keep the remote control on.
2. Press the remote’s Power button for 5 seconds > Let it turn off. 
3. Hold the Power button for 3 seconds to turn it on. Do not let go of the button.

   

4. Repeat steps 3 and 4, 4 times > The LED strips should show contrasting colors. 
5. Finally, it will switch to yellow, indicating the remote has been successfully restored. 

RGB LED controller malfunctioning was an annoying issue, though I was able to fix it quickly by resetting my remote. After the reset, I had to re-sync the remote and the LED strips and make customizations. In addition, these methods will work for most RGB devices as almost all remotes are programmed the same way.  

More About RGB:

• Motherboard RGB Header: What, Where & How
• Explained: How To Change RGB On AMD Wraith Prism Cooler?
• RGB In Gaming: Everything To Know

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

How To Reset RGB LED Controller? [With Pictures] is a post from Tech4Gamers - All About Technology And Gaming News

Key Takeaways

• GPUs need to be removed when they are ill-functioning, or they need to be upgraded.
• Integrated graphics cards can not be removed, while dedicated graphics cards can be removed. 
• If done properly, removing the GPU from the motherboard is not too difficult or risky.
  

The GPU is placed on the motherboard on the PCIe x16 slot. This is a connector where a graphics card lies.

To unplug or safely remove your GPU, follow the below steps:

1. First, turn off your computer.
   
   WARNING: Do not open the PC when it is ON.
2. Now, locate your GPU (as mentioned earlier, it will be there in the PCIe x16 slot) > unplug any cable connected to it.
   
   

   

3. To unplug the cable, press onto the plastic clip at the upper beginning of it and push it outside.
4. To take the whole GPU out, you must first untighten it with a screwdriver.
   
   Tip: Sometimes, your switchboards are short-circuited and might send the current even though they are physically turned off. This is why unplugging the cables connecting the motherboard to the switchboard is necessary.
5. Furthermore, to remove your GPU, you must first depress a small retention clip underneath your GPU on the right side of the PCIe x16 slot.
6. Pull the GPU slowly, and it should come off from the motherboard. 

It seems tricky to do it without someone who knows it professionally. But believe us, it is pretty easy, and we are saying this from experience.

How To Tell If A GPU Needs To Be Changed

If you’re a heavy graphics user, you must closely monitor your graphics processing unit (GPU). Over time, as you use more demanding applications and games, your GPU will show its age.

The following points are the signs that your GPU needs an upgrade:

1. Your games started to stutter or lag.
2. The quality of your graphics started to degrade.
3. You’re experiencing more screen tearing or GPU artifacting. 
4. Your GPU is running at or near its maximum temperature.

Hence, if you come across any of these signs, understand it is time to shop for a new GPU. Don’t wait too long, though, as an outdated GPU can affect your gaming and work performance.

Dedicated Vs Integrated GPU

It is important to remember that GPUs come in two forms: integrated and dedicated. Integrated GPUs are a part of the CPU and can not be removed in any way. On the other hand, dedicated GPUs are a separate component, and you can remove and replace them. 

Dedicated GPUs come in different shapes and sizes. They are more powerful than integrated GPUs and are attached directly to the motherboard. 

Related Articles:

• 5 BEST GPUs For i5-13600K In 2023
• The BEST Graphics Cards For 4K In 2023
• Best Graphics Card Under $300 In 2023 [Best Performance]

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

How To Remove GPU From The Motherboard is a post from Tech4Gamers - All About Technology And Gaming News

Key Takeaways

• You can cycle between colors with the Fn+Pause/Fn+Break or Fn+Left/Fn+Right keys.
• Enable the backlit mode by pressing the Fn+SL or the Fn+Esc keys.
• Reconnect your keyboard to the PC or restart the computer to troubleshoot backlighting problems.

How To Change MageGee Keyboard Color?

You can cycle between colors on a MageGee Keyboard by pressing the Fn+Pause/Break keys. Experiment with different color options until you find the best one. Then, save the color mode with Fn+Scroll (SL) keys. Moreover, the common colors found in most MageGee Keyboards are as follows:

• Blue
• Red
• Green
• Pink
• Cyan
• Orange
• Purple

How To Turn On Backlighting On MageGee Keyboard?

Backlighting is essential to be able to see the changes you make to the keyboard color. If you haven’t already backlit your keyboard, you can simultaneously press your keyboard’s Fn and Scroll (SL) keys.

On the other hand, some models, like the MageGee GK710 Gaming Keyboard, use the Fn+Esc keys to turn the backlit feature on or off.

Customizing Common Key Combinations

The MageGee MK1 lets you experiment with three lighting layouts for certain key combinations.

The following are the distinct lighting layouts offered by MageGee:

• Press the Fn+1 keys to customize the Gaming keys (WASD) and the Arrow keys.

  

• Fn+2 highlights the number panel above the Alphabet keys.

  

• With Fn+3, you can adjust colors for the Alphabet and Arrow keys.

  

Light Up Custom Keys

Here’s how you can enable backlighting for individually selected keys:

1. Hold Fn + Backspace.
2. Press the keys you wish to highlight.
3. Save the customization with the same key combination mentioned above.

Here’s how you can undo the changes made:

1. Hold the Fn key.
2. Press Backspace + Esc in the same order, and make sure not to let go of the Fn key.
3. Press the highlighted keys individually to remove lighting.
4. Once done, hit Backspace and release the Fn key.

Lighting Shortcut Keys

The following key pairs control aspects of your keyboard’s lighting, such as brightness, color patterns, and more:

• Fn+Up/Fn+Down: Adjusts brightness. Moreover, the three lights on the top right, just above the “Numeric Pad,” begin to flash once you have reached the minimum or maximum brightness settings.

  

• Fn+Left/Fn+Right: Sets the direction in which light flows across your keyboard, such as Left to Right or Right to Left.

  

• Fn+Plus (+)/ Fn+Minus (-): Controls the speed of light animation.
• Fn+SL: Returns to the default lighting preset.

Different Lighting Modes On MageGee Keyboard

The diverse lighting modes in MageGee Keyboards enhance your gameplay and make the essential keys easier to navigate in the dark.

• Soft Breathing Effect: The backlight calmly fades in and out to produce a soft, breathing-like effect.
• Glowing Effect: The colors slowly appear behind the keys.
• Highlight Effect: The light turns on only for the keys you press and fade as you hit the next key.
• Ripple Effect: It creates a ripple effect from the key you tap. The colors spread outward until they finally stretch to the edges of the keyboard.
• Shooting Light Effect: In this mode, you will see a lighting effect in the row of the triggered key. For example, if you press the Z key, the lights travel across the entire row.
• Raindrop Effect: It mimics a rainy surface, as the color lightly fades for the chosen key, while it stays stable for the other keys on the keyboard.
• Glowing Embers Effect: The effect produces soothing ember-like colors and shades under the keys.
• Spiral Effect: Lights travel across the keys in a spiral pattern. 

What To Do If The Background Color Is Not Changing?

I have a few tips to help you troubleshoot your MageGee Keyboard in case it fails to switch colors despite using the above-mentioned methods.

• Ensure you have properly connected the MageGee Keyboard to your computer.
• Verify that your keyboard model has a backlit color-changing feature.
• Reconnect your keyboard to the computer.
• Restart the computer.
• Refer to the keyboard’s manual and verify you are pressing the right keys.

Related Keyboard Articles:

• How To Change HyperX Keyboard Color
• How To Change Color On SteelSeries Keyboard?
• How To Change Color On Redragon Keyboard
• How To Change Color On Razer Keyboard?

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

How To Change MageGee Keyboard Color? is a post from Tech4Gamers - All About Technology And Gaming News

Key Takeaways  

• Razer keyboards offer their users a wide variety of lighting effects and colors to choose from when lighting their keyboards.  
• You can turn on RGB on your Razer keyboard by pressing FN + F9 shortcut keys. 
• To customize the lighting on your Razer keyboard, you can use Chroma Studio, Razer Synapse 2, Razer Synapse 3, and other methods.

How To Change Color On Razer Keyboard With Keyboard Shortcuts?

On your Razer keyboard, press FN + Ctrl + 1-7 to change the color of the lighting on your keyboard. This is a simple and time–saving option to customize your keyboard lighting. To customize these color profiles, you’ll have to use Razer Synapse. 

How To Change Color On Razer Keyboard Using Chroma Studio?

Here’s how you can change the color of your Razer keyboard using Chrome Studio:

1. First, open Razer Synapse on your computer and select Chroma Studio under Modules. 
2. Start by selecting an effect under the Add Effect option in the Studio tab. 
3. Now, choose the Chroma effect. It will be added to your layers. So, to create your Chroma effect, different options are available on the toolbar, including Selector (Ctrl + S), which allows you to develop the highlighting development a Pen (Ctrl + P), which enables you to draw on LEDs, Paint Bucket (Ctrl +B). Move and remove tools to drag the positions or delete the entire product. 
4. Next, choose the keys you’ve decided to show the effect.
5. One way to select the keys is to choose directly on the keyboard or via the Quick Selections menu.
6. Select the key, and choose the color in the ‘EFFECTS’ settings on the right. You can also select different gradient patterns. Another important thing is every effect on Synapse has its speed, playback, density, and angle options. Choose your favorite product and then click on Save. 
7. Additionally, the left side of the screen shows you the custom effects, so you know what you have created. 

How To Change Razer Keyboard Color With Synapse 2.0?

Here’s how you can change the color of your Razer keyboard using Synapse 2:

1. Start by opening Synapse 2, then select your Razer keyboard from the devices connected to your PC.
2. Click on LIGHTING. Here, you can customize anything from brightness, effects, colors, and more. 
3. Save your custom lighting profile and learn its assigned shortcut.
4. Use the shortcut to switch to the colors at any time.

How To Change Razer Keyboard Color With Synapse 3.0?

Here’s how you can change the color of your Razer keyboard using Synapse 3:

1. Open Synapse 3, select your Razer keyboard, and click ‘Lighting’ 
2. Once you hit the EFFECTS panel, change the color and effects to your liking.  
3. Click on the ‘Switch lighting’ option to switch between your desired lighting effects.  
4. Click on Keyboard > Customize button > Switch lighting.
5. Choose your preferred illuminating effect, and then click Save

This way, you can alter the default colors and effects of the Razer keyboard. 

Abdul Hadi

[How To’s & Guides Editor]

Haddi has been in the Gaming and tech Space for over 10 Years Now; he has worked on notable websites like eXputer, Gamepur, Gear Siege, Gearnuke, and plenty more. He is an expert at Games & PC Hardware; you can expect him to solve any problem. People often joke, that if there is any problem anyone can solve, Haddi can solve it faster. Currently, Haddi writes and manages a Team of Experts at Tech4Gamers.

Contact: Haddi@tech4gamers.com

Step By Step: How To Change Color On Razer Keyboard? is a post from Tech4Gamers - All About Technology And Gaming News